makerbot replicator 2 spool holder 3d models

The back pieces print together to aid spacing and placement on the Glass Bed. Glue them to the glass as one unit before cutting off the connecting tab. Slide the notches around the rear clamp of the platform. Print settings include a layer height of...

Laser-cut from 2mm aluminium, these support brackets prevent the build platform from sagging and vibrating, resulting in print quality issues. To install, replace original screws on the plastic arms with longer ones (M3x30 suggested, though slightly...

This part is a door handle and latch designed to fit flush with the 2X style printers featuring metal frames and routed plastic (foamed PVC) panels. It attaches to a hole in a lasercut 3mm Acrylic panel, as seen on Thingiverse at...

These are support brackets lasercut from 2mm thick aluminium that will help prevent the buildplatform from sagging and vibrating which cause quality issues on prints. They fit snuggly, just replace the original screws on the side of the plastic...

The design is optimized for use with M5 screws, and it's only intended for experimentation if you have a spare Ultimaker 2 Spool holder you want to mount on another printer or in a different location. ... Print Settings: Printer Brand: Prusa i3 Printer:...

Remix of RODAM Spool Holder with increased length to fit bigger 2.5kg (5.5 lbs) spools. It should fit spools up to around 11cm (4.3 inches) wide. It uses standard 608 bearings (you can use ZZ/2Z type or the more expensive 2RS). !! make sure to...

Remix of RODAM Spool Holder with increased length to fit bigger 2.5kg (5.5 lbs) spools. It should fit spools up to around 11cm (4.3 inches) wide. It uses standard 608 bearings (you can use ZZ/2Z type or the more expensive 2RS). !! make sure to...

Hi, This is modified Universal Filament Spool Holder by butchja (https://www.thingiverse.com/thing:2070272) The changes from the original design are: - Assembly length adjusted according to Snapmaker 2.0 - Possible to use this filament spool holder...

I really love my Lulzbot Mini 2, but I wasn't too fond of the squeaking that occasionally occurred as filament spools rubbed against the edge of the integrated folding arm. I experimented with a few different spool holder designs, but couldn't find...

To ensure proper fitting of filament spools, note that MakerBot originals measure 50mm, whereas most Chinese-made alternatives have a 38mm center hole diameter. To use these smaller spools, consider the following steps: firstly, select exterior...

This adapter mounts to the original spool holder allowing you to use third party filament reels.

Holder remix https://www.thingiverse.com/thing:5501382 Tools storage for spool holder: https://www.thingiverse.com/thing:6108794

The Anycubic PREDATOR is a basic 2.5 spool holder designed for use with standard 1 kg stirrups. To set it up, you'll need four bearing 608 units, one M8 screw, and one M8 nut. To secure the holder to the vertical stirrup, simply attach it using an...

Spool holder remix for FB Reborn 2 printer, using holes for regular holder. Use holding nut from https://www.thingiverse.com/thing:2070272 or https://www.thingiverse.com/thing:4855918. Need 2pc M3x10 or M3x12 screws and M8x140 thread rod. ...For...

Spool holder remix for FB Reborn 2 printer, using holes for regular holder. Use holding nut from https://www.thingiverse.com/thing:2070272 or https://www.thingiverse.com/thing:4855918. Need 2pc M3x10 or M3x12 screws and M8x140 thread rod. ...For...

A Rapman 3.2 3D printer requires a wire spool holder, which features a 3D-printed support angle and acrylic plates cut with a laser. The 4mm thick acrylic parts need gluing, and the holder attaches to the standard acrylic support cross. ...Share your...

Secure 2mm Plexiglas to the edges of the Replicator 2/2X openings using a clip.

Corner Mount for Dropcam Replicator 2 - Easy Installation and Secure Connection

Clip to hold 2mm plexiglass to sides of Replicator 2/2X openings. ... Category: 3D Printer Accessories

This is a Custom made filament spool holder for the Anycubic Kobra 2,it can be screwed into the 2 pre installed inserts, I used 2 Screws from the printer's power supply bracket, see the screws original location in the image provided (I think they are...

Hey everyone, I've got yet another part for the Neptune 2, this part should improve the conversion to direct drive extruder (Micro Swiss DD) by also rotating ther Filament Spool 90° to match the routing i made to Simplify things i printed this Spool...

Created a push-fit spool holder for the Solidoodle 2, utilizing 608 bearings in the design. To assemble it completely, print both parts twice. No screws are needed to mount it; simply push the holder onto the frame and it will fit tightly into...

I used Tinkercad to adapt a Tronxy Crux 1 spool holder (that I had previously modified) to a Creality Ender 2 Pro keyed type so I could run small spools on my Ender 2 Pro.  Most of the small holed spools are cheap filament or specialty filaments.  It...

This is a new spool holder - designed to fit the standard spindle on the Neptune 2, with a filament spool inner diameter of 78mm or thereabouts. It works - you will need two - I decided to save PLA by keeping it short. ... Please feel free to...

I remodeled the Voron spool holder to make a larger one for my eSun 3kg filament roll.I've included the reconfigurable SW file so you can easily modify the spool width and the holder height. ...I recommend higher spool holder for heavier and large...

This is an element that allows you to use the original spool holder from the official voron design and is used to move the spool above the printer.

A spool holder designed to accommodate various types of filaments, as long as the spool's width is less than 10 centimeters.

This will relocate your spool holder to a more convenient location for the filament to enter the run out detector. This will not fit a stock Neptune 2 with the foam stick on feet. It needs a minimum of 5mm clearance to the bench top. ... Printing: I...

This spool holder was inspired by other Air 2 designs and utilized VeimoX's Catia files, which were imported into Autodesk Inventor for design. The holders use existing assembly bracket screw holes with 30mm long M4 screws to accommodate the...

The new Ultimaker 2+ printer now includes a spool holder that measures 55mm in length, which unfortunately cannot accommodate the 65mm filament reels used by FormFutura. To address this issue, we have redesigned an extended version of the spool...